全国销售免费服务电话 400-886-0537
联系销售专员
滚轮罐耳
滚轮罐耳
单轮
滚轮罐耳
双轮
Roller lug

滚轮罐耳

承载能力大、运行平稳、可靠性高、寿命长

底座等零部件采用新型材料,整体结构强度更高,抗
冲击性强。

The base and other parts are made of new materials, with higher overall structural strength and strong impact resistance.

滚轮罐耳

缓冲性能好、运行稳定、调节简便、安全可靠

滚轮罐耳沿罐道运行时,因罐道的设计安装,会产生接点、弯曲高点,轮头会受到水平推力作用,由于支臂架、
底座和缓冲器之间的铰接作用,使缓冲器受压缩产生反弹力。

When the roller can ear is running along the tank way, due to the design and installation of the tank channel, the contact point and bending high point will be generated, and the wheel head will be affected by horizontal
thrust. Due to the hinge action between the support arm, the base and the buffer, the buffer will be compressed and produce rebound force.

缓冲器的反弹力:

一是保证提升容器顺利通过高点;
二是保证提升容器不得与罐道发生碰撞;
三是要保证提升容器在上升和下降过程中摆动幅度不得太大。

所以缓冲器的缓冲性能是严格按提升容器的重量、运行速度进行设计的,但其 轮头最大水平推力一定要小于或等于行业标准的要求。根据以上 理论设计制造出的滚轮罐耳能够有效满足用户要求。

型号参数

滚轮罐耳用于立井提升容器(箕斗、罐笼、平衡锤),为其提供导向和缓冲。

Roller ears are used for vertical shaft lifting containers (skip, cage, counterweight) to provide guidance and buffer.

滚轮罐耳
单轮 双轮
型号 滚轮直径mm 最大水平力KN 缓冲行程mm
单轮 L25 250 12 10~14
L30 300 16 10~14
L35 350 24 10~14
L42.5 425 33 10~14
L45 450 35 10~14
L50 500 36 10~14
双轮 LS30 300 20 10~14
LS35 350 28 10~14
LS42.5 425 42 10~14
LS45 450 44 10~14
LS50 500 45 10~14

产品特点

弹簧浸油润滑,动态特性好,弹力稳定,是国家大力推广的绿色环保产品。本产品有多种规格,能满足客户的各种需求。

Spring oil lubrication, good dynamic characteristics, stable elasticity, is a green environmental protection product vigorously promoted by the state.
This product has a variety of specifications, can meet the needs of customers.

滚轮罐耳
运行平稳、可靠性高 Stable operation and high reliability

承载能力大、寿命长、调整维修方便;
底座等零部件采用新型材料,整体结构强度更高抗冲击性强。

滚轮罐耳
磨损度低、使用寿命长 Low wear and long service life

缓冲器复位压力小,可有效地避免滚轮与罐道产生异常碰撞。通过杠杆传递
到减震筒上,同时起到导向、缓冲与稳定作用。

滚轮罐耳Roller lug

缓冲装置采用符合弹性体缓冲结构,性能稳定,免维护。

罐道与罐耳由滑动摩擦变为滚动摩擦,因此减少了动力消耗,降低了噪音,罐道和罐耳的磨损也
大大降低。从而,提高了罐道和罐耳的使用寿命。

滚轮罐耳

故障分析及排除

滚轮端盖中心孔上安装有密封塞,同时端盖上设有通气孔,真正做到新油易入,旧油易出。

A sealing plug is installed on the center hole of the roller end cover, and a vent hole is set on the end cover to make the new oil easy to enter and the old oil to come out easily.
滚轮罐耳

轮轴

支架

缓冲装置

底座

故障现象一:

滚轮转动不灵活
1、原因分析:轴承损坏
排除方法:更换轴承
2、原因分析:轴承游隙太小
排除方法:拆下副轮毂,用圆螺母调整轴承游隙
3、原因分析:密封损坏,轴承腔进污物
排除方法:清洗轴承,更换密封,注入适量润滑脂

故障现象二:

胶轮磨损快且易损坏
原因分析:滚轮与罐道接触过紧原因分析:轴承缺少润滑脂
排除方法:调整滚轮接触到罐道即可,不要加预紧力

故障现象三:

滚轮轮毂有过热现象
原因分析:轴承缺少润滑脂
排除方法:注入适量润滑脂

  • 滚轮罐耳
    质量保障
  • 滚轮罐耳
    安装便捷
  • 滚轮罐耳
    精选材质